Welcome to contact us through online consulting, emails and hotline if you are interested in our company or products. Our staff will reply you within 24 hours.
Material Availability of 1.4571 and 1.4404 Stainless Steel. Choosing between the both, grade 1.4404/316L is the preferred choice worldwide. Only in Germany, Austria and in Eastern European countries, 1.4571 is applied as acid-resistant steel.(plate) Core 304/4301 EN 1.4301, ASTM TYPE 304 / UNS S30400 material en1008(steel) General characteristics. Core 304/4301 is a classic 18% chromium, 8% nickel austenitic stainless steel. Its an all-purpose product with good corrosion resistance and is suitable for a wide variety of applications that require good formability and weldability.
May 30, 2020EN 1.4028 stainless steel is a martensitic stainless steel formulated for primary forming into wrought products. 1.4028 is the EN numeric designation for this material. X30Cr13 is the EN chemical designation. It has a moderately low embodied energy among the wrought martensitic stainless steels in the database.(plate) Estimated Reading Time 1 minEN 1.4021 (X20Cr13) Stainless Steel : (steel) May 30, 2020EN 1.4021 stainless steel is a martensitic stainless steel formulated for primary forming into wrought products. 1.4021 is the EN numeric designation for this material. X20Cr13 is the EN chemical designation. It has a moderately low embodied energy among the wrought martensitic stainless steels in the database.
VALBRUNA NORDIC AB EN 10088-3 1.4057 0805 EN 10088-3 1.4057 - QT 800 A hardenable stainless steel Typical analysis % C 0,20 Cr 16 Ni 2 Norms Steel grade EN 10088-3/95 QT 800 1.4057 ASTM A276 ( Type 431 ) Delivery condition Quenched and tempered ( Replaces SS 2321 -03 ) EN 1.4057 is a hardenable stainless steel containing(plate) Estimated Reading Time 6 mins1.4301 Chromium-nickel austenitic stainless steel (steel) 1.4301 is weldable with or without the use of filler material. If the use of a filler metal is required, then the use of Novonit&4316 (AISI 308L) would be recommended. Maximum interpass temperature 200 °C. Post weld heat treatment is not necessary. 1.4301 is usually heated to within the range 1150 °C 1180 °C to allow forging to take
ALLOY 1.4162 / UNS S32101 / LDX 2101 is a low Ni-alloyed duplex with balanced chemistry of chromium, molybdenum and nitrogen content.(plate) File Size 49KBPage Count 2Material No. 1.4404 - M.Woite GmbH(steel) DIN EN 10088-2 (09/2005) stainless steel; sheet metal and ribbons out of corrosion resistant steel for general purposes DIN EN 10088-3 (09/2005) stainless steels.Technical delivery conditions for semi-finished products,bars,rods,wire selection and bright products of corrosion resisting steels for general and construction purposes
S165M is a high strength low carbon martensitic/ austenitic stainless steel. It combines high strength, good fatigue resistance with good weldability.(plate) Sanmac 304/304L Sandvik Materials Technology(steel) Oct 31, 20191 MPa = 1 N/mm 2 a) R p0.2 and R p1.0 corresponds to 0.2% offset and 1.0% offset yield strength, respectively. b) Based on L 0 = 5.65S 0, where L 0 is the original gauge length and S 0 the original cross-section area.. Impact strength. Due to its austenitic microstructure, Sandvik SANMAC 304/304L has very good impact strength both at room temperature and at cryogenic temperatures.
Property data given in this document is typical for bar products covered by EN 10088-3:2005. ASTM, or other standards may cover products sold. It is reasonable to expect specifications in these standards to be similar but not necessarily identical to those given in this datasheet. material en1008 Material supplied by the Company may vary significantly from material en1008(plate) Stainless Steel EN 1.4301 AISI 304 X5CrNi18-10 UNSS30400(steel) Reliable Steel is one of the leading manufacturers, exporters, stockiest, distributors, dealers and suppliers of superior quality Stainless Steel & High Nickel Alloys Pipes, Tubes, Plates, Sheets, Round Bars, Fittings & Forgings in different specifications, which find application in high demanding industries and sectors, particularly high temperature and corrosive services.
1.4542 X5CrNiCuNb16-4 - - DIN EN 10088-3 AISI 630/ 17-4 PH 1.1191 C45E - - DIN EN 10269 - 300 1.4401 X5CrNiMo17-12-2 A4 W2 DIN EN 10269 -AISI 316 1.4301 X5CrNi18-10 A2 W2 DIN EN 10269 -AISI 304 Non-magnetizable steels Werkstoff Nr. DIN / EN Material 1.3948 X4CrNiMnMoN 19 13 8 - 1.3952 X2CrNiMoN 18 14 -(plate) material en 10088(steel) en 10088 2 us equivalenten 10088 3 astm equivalentdin en 10088 3din en 10088 3 pdfbs en 10088en 10083 1 us equivalenten 10088 1 pdfen 10088 2 standardmaterial en 10088.Do you want results only for material en1008?Some results are removed in response to a notice of local law requirement. For more information, please see here.
Was this helpful?People also askWhat is en 10088 stainless steel?What is en 10088 stainless steel?EN 10088 Stainless steels Professional Supplier of material en1008(steel) Created Date 4/5/2006 11:02:33 AM